MK EP 500 R

MK EP 500 R is a two-component epoxy resin (resin + hardener) not loaded indicated for the bonding of different materials.

RAPID two-component epoxy resin (resin + hardener) not loaded indicated for the bonding of different materials.

  • Mainly used for bonding metals (aluminum, steel, iron) and composite materials
  • Suitable for the assembly of rigid plastics, marble, porcelain, ceramics, costume stones, hardwoods, glass and ferrite
  • Very fast setting
  • Rapid repair even at temperatures close to 0 °C
  • Solvents free
  • Resistant to bases, diluted acids and poor to solvents
  • No shrinkage
  • Excellent adhesion on different substrates, even without the use of specific surface primers

Attachment

TDS MK EP 500R

Description

PROPERTIES RESIN HARDENER
CHEMICAL NATURE Epoxy Resin Mercaptan
COLOUR Straw Yellow Amber
DENSITY at 25 °C (ASTM D 1475) 1,15 – 1,19 g/ml 1,11 – 1,15 g/ml
VISCOSITY at 25 °C (EN13702-2) 6.000 – 8.000 mPa.s 10.000 – 18.000 mPa.s
VOLUME RATIO 1 1
TYPICAL CHARACTERISTICS OF THE MIXED PRODUCT
OPEN TIME @ 25 °C 3 – 4 minutes
POT LIFE 8 – 12 minutes
FIXTURE TIME 2 hours
FULL CURE TIME (6mm, 25°C) 24 hours
EXOTHERMIC PEAK OF THE REACTION 70 °C
DENSITY (ASTM D 792) 1,13 – 1,17 g/ml
HARDNESS (ASTM D 2240) 75 – 80 Shore D
MINIMUM GAP FILL 0,50 mm
TENSILE STRENGHT (Metal / Metal) 20 N/mm2
TENSILE ELONGATION < 10 %
TEMPERATURE RESISTANCE – 40 / + 70 °C
WATER RESISTANCE Good

 

Additional information

Specific work-setting (component)

Operating Temperature <0 ° C, STATIC bonding-line <100 cm (LIGHT HANDLING)

Type of joint (application mode)

BEAD – OVERLAP, SMALL POINT – DROP

Substrates (suitable adherings match))

ARAMIDE FIBER-REINFORCED COMPOSITES # ARAMIDE FIBER-REINFORCED COMPOSITES, ARAMIDE FIBER-REINFORCED COMPOSITES # GLASS REINFORCED FIBER COMPOSITES, ARAMIDE FIBER-REINFORCED COMPOSITES # METALS and/or ALLOYS (Al – Ti – Ni – Cr – Fe), CARBON FIBER-REINFORCED COMPOSITES # CARBON FIBER-REINFORCED COMPOSITES, CARBON FIBER-REINFORCED COMPOSITES # GLASS REINFORCED FIBER COMPOSITES, CARBON FIBER-REINFORCED COMPOSITES # METALS and/or ALLOYS (Al – Ti – Ni – Cr – Fe), CARBON FIBER-REINFORCED COMPOSITES # METALS and/or ALLOYS (Cu / Zn – Fe – Pb), GLASS # METALS and / or ALLOYS (Al – Ti – Ni – Cr – Fe), GLASS REINFORCED FIBER COMPOSITES # GLASS REINFORCED FIBER COMPOSITES, GLASS REINFORCED FIBER COMPOSITES # METALS and / or ALLOYS (Cu / Zn – Fe – Pb), GLASS REINFORCED FIBER COMPOSITES # METALS and/or ALLOYS (Al – Ti – Ni – Cr – Fe), METALS and / or ALLOYS (Al – Ti – Ni – Cr – Fe) # METALS and / or ALLOYS (Al – Ti – Ni – Cr – Fe), METALS and / or ALLOYS (Cu / Zn – Fe – Pb) # METALS and / or ALLOYS (Al – Ti – Ni – Cr – Fe), METALS and / or ALLOYS (Cu / Zn – Fe – Pb) # METALS and / or ALLOYS (Cu / Zn – Fe – Pb), SEMI-FINISHED BUILDINGS # METALS and / or ALLOYS (Cu / Zn – Fe – Pb)

Adhesive Working Time

< 10 MINUTES

Adhesive Fixture Time

< 10 MINUTES

Type of failure mode (after joint stress)

ADHESIVE (bonding failure between adhesive and adhering: no residue on substrates), COHESIVE (bonding failure inside the adhesive: residue presence on substrates), SUBSTRATE ((adhering structure failure: adhesive causes a fracture on substrate)

component sector/process

AUTOMOTIVE – TRUCK – BUS – AGRICULTURAL, FORESTRY MACHINES, INDUSTRIAL COMPONENTS, MILITARY DEFENCE, SPORT, TRAINS

Whatsapp Contact Adhesive